Sign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
In Renesas RL78 how we can see option for watch window variable while running time.
Dear Raja, Please see the below steps & follow instructions.... 1. Click on RL78(Debug Tool) then see new window. 2. Please check second option i.e. debug tool setting , press on this ,then see Some option there. you need to check this option "Access Memory while Running" and do yes on this "AccRead more
Dear Raja,
Please see the below steps & follow instructions….
1. Click on RL78(Debug Tool) then see new window.
2. Please check second option i.e. debug tool setting , press on this ,then see Some option there.
you need to check this option “Access Memory while Running” and do yes on this “Access by stopping execution” option.
From above step you will get running values while run time.
Please feel free to write us for further support.
Thanks & Regards
Shivali Singh
Application Engineer
See lessInput/output pin
Dear Raja, Please check the below instruction to make input and output without code generator. PM1_bit.no0 = 0; // 0 mean Ouput make, 1 means Input make P1_bit.no = 1; // high pin // Port Pin P10 Please feel free to write us for further support. Thanks & Regards Shivali Singh AppliRead more
Dear Raja,
Please check the below instruction to make input and output without code generator.
PM1_bit.no0 = 0; // 0 mean Ouput make, 1 means Input make
P1_bit.no = 1; // high pin // Port Pin P10
Please feel free to write us for further support.
Thanks & Regards
Shivali Singh
Application Engineer
See lessRL78 /G12 MCU Reset problems
Dear Raja, Please check in your code generator setting of watchdog timer, i think you enable your watch dog timer setting due to this your MCU reset again and again. If Yes, please check the below condition. 1. Go to watchdog timer setting and need to click on unused option. or 2. You need call thisRead more
Dear Raja,
Please check in your code generator setting of watchdog timer, i think you enable your watch dog timer setting due to this your MCU reset again and again.
If Yes, please check the below condition.
1. Go to watchdog timer setting and need to click on unused option.
or
2. You need call this instruction WDTE=0xAC(means this is watchdog clear register) in your code.
Please feel free to write us for further support.
Thank You
Shivali Singh
Application Engineer
See lessWriting bit/byte in EEPROM
Yes you can use WDT in this case. When power failure detected, WDT will trigger interrupt, in interrupt routine store required bit/byte in EEPROM. Once power retains read EEPROM and based on retrieved bit/byte update flag. Hope this will answer your question.
Yes you can use WDT in this case. When power failure detected, WDT will trigger interrupt, in interrupt routine store required bit/byte in EEPROM.
Once power retains read EEPROM and based on retrieved bit/byte update flag.
Hope this will answer your question.
See lessChange of SPI Baud Rate in Renesas RL78
The transfer clock frequency for 3-wire serial I communication can be calculated by the following expressions.(1) For Master(Transfer clock frequency) = {Operation clock (fMCK) frequency of target channel} ÷ (SDRmn[15:9] + 1) ÷ 2 [Hz](2) For Slave(Transfer clock frequency) = {Frequency of serial cloRead more
The transfer clock frequency for 3-wire serial I communication can be calculated by the following expressions.
(1) For Master
(Transfer clock frequency) = {Operation clock (fMCK) frequency of target channel} ÷ (SDRmn[15:9] + 1) ÷ 2 [Hz]
(2) For Slave
(Transfer clock frequency) = {Frequency of serial clock (fSCK) supplied by master}Note [Hz]
Note :The permissible maximum transfer clock frequency is fMCK/6.
Remark :The value of SDRmn[15:9] is the value of bits 15 to 9 of serial data register (SDRmn) (0000000B to 1111111B) and therefore is 0 to 127. The operation clock (fMCK) is determined by serial clock select register m (SPSm) and bit 15 (CKSmn) of serial mode register mn (SMRmn).
Configuration using .dp vision in Infineon XDPL series IC .
Hi Manoj, Please go thorugh the page no.21 to 24 of the given link and follow the steps given. Please find the link below. https://www.infineon.com/dgdl/Infineon-ApplicationNote_ReferenceBoard_REF-XDPL8105-CDM10V-ApplicationNotes-v02_00-EN.pdf?fileId=5546d462584d1d4a0158962cb4ed4315
Hi Manoj,
Please go thorugh the page no.21 to 24 of the given link and follow the steps given. Please find the link below.
See lesshttps://www.infineon.com/dgdl/Infineon-ApplicationNote_ReferenceBoard_REF-XDPL8105-CDM10V-ApplicationNotes-v02_00-EN.pdf?fileId=5546d462584d1d4a0158962cb4ed4315
Configuration of Infineon CDM10VD
Hi Manoj, Please find below, the answer to your query. Please go thorough the pg no 25-26 fo the given link. Please find the link below. https://www.infineon.com/dgdl/Infineon-ApplicationNote_ReferenceBoard_REF-XDPL8105-CDM10V-ApplicationNotes-v02_00-EN.pdf?fileId=5546d462584d1d4a0158962cb4ed4315
Hi Manoj,
Please find below, the answer to your query.
Please go thorough the pg no 25-26 fo the given link. Please find the link below.
See lesshttps://www.infineon.com/dgdl/Infineon-ApplicationNote_ReferenceBoard_REF-XDPL8105-CDM10V-ApplicationNotes-v02_00-EN.pdf?fileId=5546d462584d1d4a0158962cb4ed4315
LED Driver- BP3338A IC
Dear Rakesh, please find the enclosed reference design tool it will be helpful for the calculation of all transformer-related data, and for formulas, which you can see in the excel sheet. Thanks Sandeep
Dear Rakesh,
please find the enclosed reference design tool it will be helpful for the calculation of all transformer-related data, and for formulas, which you can see in the excel sheet.
Thanks
Sandeep
See lessWhich ESP module have Built-in ATECC608A chip
There is a module ESP32-WROOM-32SE which have built-in ATECC608A chip.
There is a module ESP32-WROOM-32SE which have built-in ATECC608A chip.
See lessCode generated by CS+ could not enable interrupt.
The hardware U/M contains the information required to access I/O and peripherals among other things. RH850/F1KM, RH850/F1KH User's Manual: Hardware (R01UH0684EJ0110) Sample code is available to demonstrate many of the concepts. Y-ASK-RH850F1KM-S4-V3 Software Package.
The hardware U/M contains the information required to access I/O and peripherals among other things. RH850/F1KM, RH850/F1KH User’s Manual: Hardware (R01UH0684EJ0110) Sample code is available to demonstrate many of the concepts. Y-ASK-RH850F1KM-S4-V3 Software Package.
See less