Sign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
Renesas RH850 CS+ IDE Program Execution Issue
In CS+ CC IDE for RH850,when debug tool is connected click on Debug tool settings then click on Flash Options Settings ,OPBT0 as DA20FDCF and OPBT1 as FFFFFDFF for LPD-1 and OPBT0 as BA20FDCF and OPBT1 as FFFFFDFF for LPD-4 and issue is solved program executes continuously .
In CS+ CC IDE for RH850,when debug tool is connected click on Debug tool settings then click on Flash Options Settings ,OPBT0 as DA20FDCF and OPBT1 as FFFFFDFF for LPD-1 and OPBT0 as BA20FDCF and OPBT1 as FFFFFDFF for LPD-4 and issue is solved program executes continuously .
See lessRenesas RL78 Flashing error in CS+
In Renesas CS+ IDE, Goto Code Generator(Design Tool),On-chip debug setting should be used Now Generate code and Download .
In Renesas CS+ IDE, Goto Code Generator(Design Tool),On-chip debug setting should be used
See lessNow Generate code and Download .
Renesas RH850 Flashing issue in CS+IDE
Erase Microcontroller Flash area from Renesas flash programmer software and again download software from CS+ IDE issue is solved.
Erase Microcontroller Flash area from Renesas flash programmer software and again download software from CS+ IDE issue is solved.
See lessRenesas RL78 Data Flash Memory Watch
In Renesas CS+ IDE , Goto view ->Memory->Memory1 In that DataFlash Address mentioned in Datasheet for Ex.RL78F14, F1000 DataFlash Starting Address
In Renesas CS+ IDE , Goto view ->Memory->Memory1 In that DataFlash Address mentioned in Datasheet for Ex.RL78F14, F1000 DataFlash Starting Address
See lessRenesas RL78 Flashing issue in CS+CC
Un-install Renesas Emulator E1 or E2 or E20 driver and install again issue will be solved
Un-install Renesas Emulator E1 or E2 or E20 driver and install again issue will be solved
See lessRAM initialization in Renesas RH850 F1x
;----------------------------------------------------------------------------- ;hdwinit ; Specify RAM addresses suitable to your system if needed. ;----------------------------------------------------------------------------- LOCAL_RAM_ADDR .set 0xFEBE0000 ; for MCU : R7f701684 LOCAL_RAM_END .set 0xRead more
;—————————————————————————–
See less;hdwinit
; Specify RAM addresses suitable to your system if needed.
;—————————————————————————–
LOCAL_RAM_ADDR .set 0xFEBE0000 ; for MCU : R7f701684
LOCAL_RAM_END .set 0xFEBF7FFF ; for MCU : R7f701684
RETENTION_RAM_ADDR .set 0xFEBF8000 ; for MCU : R7f701684/R7f701690 ; 0xFEBE0000
RETENTION_RAM_END .set 0xFEBFFFFF ; for MCU : R7f701684/R7f701690 ; 0xFEBF7FFF
Implementation of USB and SCI Boot mode for RA MCU series
For USB boot mode Target Board: EK-RA2A1 Steps to follow: Step1: USB FS is used for this mode, Connect Device USB (J9) on EK-RA2A1 board. Step2: Power the board using Debug USB or external Power. Step3: Press the RESET button(S2), once done you can find the comport detected. Step4: Open the RFP toolRead more
For USB boot mode
Target Board: EK-RA2A1
Steps to follow:
Step1: USB FS is used for this mode, Connect Device USB (J9) on EK-RA2A1 board.
Step2: Power the board using Debug USB or external Power.
Step3: Press the RESET button(S2), once done you can find the comport detected.
Step4: Open the RFP tool and create project as below, In Tool select COM Port, COM 12 detected automatically(verify in ports RA USB Boot (CDC) (Com 12) ).
Step5: Once Project is successfully created, Browse the .SREC file in debug folder of your project for eg: E:\MOHAN ..PATH \RA2L1\Workspace\EK_RA2A1_LED\Debug\EK_RA2A1_LED.srec
STEP6: Again press RESET button S2, and give Start, Once Completed you will find like below (Refer attached docx file).
STEP7: Do a power cycle, so that the application will be running.
Note: Procedure attached with snapshots.
See less