Sign Up

Sign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.

Have an account? Sign In
Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Have an account? Sign In Now

Sign In

Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.

Sign Up Here
Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Forgot Password?

Don't have account, Sign Up Here

Forgot Password

Volt.Tech

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

Have an account? Sign In Now

You must login to ask question.

Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Forgot Password?

Need An Account, Sign Up Here

Please briefly explain why you feel this question should be reported.

Please briefly explain why you feel this answer should be reported.

Please briefly explain why you feel this user should be reported.

volt.tech Logo volt.tech Logo
Sign InSign Up

volt.tech

volt.tech Navigation

  • Home
  • About Us
  • Contact Us
Search
Ask A Question

Mobile menu

Close
Ask a Question
  • Tags
  • Category
    • Amplifiers
    • Passives & Protection
    • Clocks & Timing
    • Diodes & Rectifiers
    • FPGAs & PLDs
    • Interface ICs & Transceivers
    • LEDs & Optoelectronics
    • Memories
    • MEMS & Sensors
    • Microcontroller
    • Power Management
    • RF & Microwave
    • Security & Smart Card
    • Motor Drivers
    • Wireless Connectivity
  • Groups
  • Add group
  • Badges
  • Help
  • Home
  • About Us
  • Contact Us
Home/xdpl

volt.tech Latest Questions

Manoj
  • 0
Manoj
Asked: June 14, 2022In: Power Management

Error in burning program in XDPL8210 IC

  • 0

I am getting error to update firmware when trying to burn program in XDPL8210 IC using .dpvision tool. Please advise some solution ?

I am getting error to update firmware when trying to burn program in XDPL8210 IC using .dpvision tool.

Please advise some solution ?

Read less
.dpvisionfirmwarepower managementxdplXDPL8210 IC
  1. pallavi sharma
    Added an answer on July 13, 2022 at 5:05 pm

    As the XDPL8210 chip on the 35 W reference design PCB has a first full set of parameters in its One-Time Programmable (OTP) memory space, only changed parameters are written in the OTP memory. 1 Load configuration file (see example in Figure 7). 2 Modify the parameter value needed, then press [File]Read more

    As the XDPL8210 chip on the 35 W reference design PCB has a first full set of parameters in its One-Time
    Programmable (OTP) memory space, only changed parameters are written in the OTP memory.

    1 Load configuration file (see example in Figure 7).
    2 Modify the parameter value needed, then press [File] >> [Save] or [File] >> [Save as] to save
    the configuration file. Otherwise, proceed to step 3.
    3
    (optional)
    Disconnect or turn off AC input voltage and check the hardware connection for configuration,
    see Figure 2 and Figure 3.
    4 Press to supply power and establish connection to the target XDPL8210. After this,
    XDPL8210 will enter configuration mode and the device status should change to .
    5
    Press to burn the configuration into target XDPL8210.
    After this step, a window pops up, like one of these below.

    Note: If the parameter configuration is equivalent to to the pre-existing parameters, the
    XDPL8210 will not burn them in the OTP memory.
    6 Press “Proceed” or “Yes” to burn the configuration. After this, a window pops up indicating
    success.
    7 Press “OK” on the pop-up window then disconnect the programming cable from the board
    connector and test the application, if needed.

    See less
    • 0
    • Share
      Share
      • Share on Facebook
      • Share on Twitter
      • Share on LinkedIn
      • Share on WhatsApp
  • 1 Answer
Answer

Sidebar

Ask A Question

Stats

  • Questions 388
  • Answers 374
  • Comments 0
  • Best Answers 8
  • Popular
  • Answers
  • Manoj

    Configuration using .dp vision in Infineon XDPL series IC .

    • 5 Answers
  • Linto

    Renesas RL78/G14 ADC interface code

    • 4 Answers
  • Julian White
    Julian White added an answer Hello, IrDA has hardly been used for a long time,… March 7, 2023 at 10:27 am
  • Julian White
    Julian White added an answer It's not required per se, but it's helpful. The issue… March 4, 2023 at 10:04 am
  • nidhi singh
    nidhi singh added an answer Hi Alex, The exchange mode for MCU boot uses the… March 2, 2023 at 10:37 am
  • Julian White
    Julian White added an answer Hi, Thank you for posting on the Volt.Tech community. Can… February 28, 2023 at 10:04 am
  • nidhi singh
    nidhi singh added an answer Hello, The labeling looks ok F130 = LD2981ABM30TR F133 =… February 23, 2023 at 10:27 am

Users

test27782358

test27782358

  • 0 Questions
  • 0 Answers
test17284313

test17284313

  • 0 Questions
  • 0 Answers
test1856815

test1856815

  • 0 Questions
  • 0 Answers

Explore

  • Tags
  • Category
    • Amplifiers
    • Passives & Protection
    • Clocks & Timing
    • Diodes & Rectifiers
    • FPGAs & PLDs
    • Interface ICs & Transceivers
    • LEDs & Optoelectronics
    • Memories
    • MEMS & Sensors
    • Microcontroller
    • Power Management
    • RF & Microwave
    • Security & Smart Card
    • Motor Drivers
    • Wireless Connectivity
  • Groups
  • Add group
  • Badges
  • Help

Footer

volt.tech

Volt.Tech

Find your spark

About Us

  • About Us
  • Contact Us
  • Groups

Legal Stuff

  • Privacy Policy
  • Faqs

Follow

© 2022 volt.tech. All Rights Reserved
With Love by volt.tech.