What is the sample code for interfacing Serial NAND Flash memory with Renesas RH850/F1K using Quad SPI (SFMA module).
What is the sample code for interfacing Serial NAND Flash memory with Renesas RH850/F1K using Quad SPI (SFMA module).
Read lessSign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
You must login to ask question.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
Renesas MCU as we know Renesas makes microcontrollers (mcu) that provide expand ability while allowing customers to make full use of existing resources.
Some of the popular microcontrollers (mcu) made by Renesas are:
RL78 is the family name for a range of 16-bit microcontrollers.
The RX MCU family
The RX, an acronym for Renesas Xtreme, is the family name for a range of 32-bit microcontrollers developed by Renesas.
The RA, an acronym for Renesas Advanced, is the family name for a range of 32-bit microcontrollers with Arm Cortex processor cores.
What is the sample code for interfacing Serial NAND Flash memory with Renesas RH850/F1K using Quad SPI (SFMA module).
What is the sample code for interfacing Serial NAND Flash memory with Renesas RH850/F1K using Quad SPI (SFMA module).
Read lessWhile using Renesas rh850f1k in my project , I need to check for HW reset, SW reset, WDG reset. Which register do I have to monitor to identify the reset reason?
While using Renesas rh850f1k in my project , I need to check for HW reset, SW reset, WDG reset. Which register do I have to monitor to identify the reset reason?
Read lessWhere is the FCU Firmware ? It is already present in the ECC test area or is provided by Renesas?
Where is the FCU Firmware ? It is already present in the ECC test area or is provided by Renesas?
Read lessThe FW is stored in a special area of the flash. The copy of the data from this area stored into the FCU RAM is either handled in the libraries or described in the flash hardware user's manual. For more details please contact: device_support.RH850-EU at lm.renesas.com
The FW is stored in a special area of the flash. The copy of the data from this area stored into the FCU RAM is either handled in the libraries or described in the flash hardware user’s manual. For more details please contact: device_support.RH850-EU at lm.renesas.com
See lessI am using RH850D1L2H, and facing following problem with the operation of Main Oscillator during DEEPSTOP mode. Before entering to DEEPSTOP mode, I have set the MOSCSTPM.MOSCSTPMSK = 0. If the OPBT0 – OPJTAG[1:0] = 01 (LPD 4-pin mode), the ...Read more
I am using RH850D1L2H, and facing following problem with the operation of Main Oscillator during DEEPSTOP mode. Before entering to DEEPSTOP mode, I have set the MOSCSTPM.MOSCSTPMSK = 0. If the OPBT0 – OPJTAG[1:0] = 01 (LPD 4-pin mode), the MainOsc stops operation in DEEPSTOP. If the OPBT0 – OPJTAG[1:0] = 10 (LPD 1-pin mode), the MainOsc remains operating in DEEPSTOP. I would like to know how come the MainOsc still operating and how the LPD setting act as a factor?
Remarks: System is in normal mode, no E1 debugger is connected after flashing the software.
Read lessDo you have a demo program for the Mango hardware that would demonstrate the issue? This would certainly be concerning to be true. If you can provide at minimum a hex-file that can be loaded using RFP, and the different option byte settings for each of the above two cases that can changed independeRead more
Do you have a demo program for the Mango hardware that would demonstrate the issue? This would certainly be concerning to be true. If you can provide at minimum a hex-file that can be loaded using RFP, and the different option byte settings for each of the above two cases that can changed independently of the user program, I can have this checked by FAE.
See lessWhat is the difference between Renesas RH850G3K and Renesas RH850G3KH core?
What is the difference between Renesas RH850G3K and Renesas RH850G3KH core?
Read lessRH850G3H Core has RH850/F1L (elder series) with max. 96MHz in 5 Stage pipeline, no FPU, MPU (4 areas)while RH850G3KH core has RH850/F1K (newer series) with max. 240MHz in 5 Stage pipeline, FPU, MPU (16 areas).
RH850G3H Core has RH850/F1L (elder series) with max. 96MHz in 5 Stage pipeline, no FPU, MPU (4 areas)while RH850G3KH core has RH850/F1K (newer series) with max. 240MHz in 5 Stage pipeline, FPU, MPU (16 areas).
See lessWhen you compile the code and get the error like “Could not load the file or assemble /CARL78v172.chm or one of its dependencies. The system can not find the specified file” then what will you do?
When you compile the code and get the error like “Could not load the file or assemble /CARL78v172.chm or one of its dependencies. The system can not find the specified file” then what will you do?
Read lessFor Renesas RL78/G12 family MCU, which registers are used for period and duty cycle.
For Renesas RL78/G12 family MCU, which registers are used for period and duty cycle.
Read lessHello Linto, The Register TDR00 for frequency(Period) i.e. called Master and the Register TDR01 for Duty i.e. called slave in timer.c file. Thanks & Regards Shivali Chauhan
Hello Linto,
The Register TDR00 for frequency(Period) i.e. called Master and the Register TDR01 for Duty i.e. called slave in timer.c file.
Thanks & Regards
Shivali Chauhan
See less
Please refer to RESF and the redundant RESFR:
Please refer to RESF and the redundant RESFR: