Home/mcus

volt.tech Latest Questions

ashishgawade
  • 0
ashishgawade
Asked: December 14, 2022In:
  • 0

Helllo, The release notes for the latest update for Segger’s J- Link software had this in them (J- Link- OB- XMC4200) Added support for ARM Cortex-M23, and Cortex-M33 cores. (XMC Link) Added support for ARM Cortex-M23, and Cortex-M33 cores. Does this indicate that Infineon ...Read more

Helllo,

The release notes for the latest update for Segger’s J- Link software had this in them

(J- Link- OB- XMC4200) Added support for ARM Cortex-M23, and Cortex-M33 cores.

(XMC Link) Added support for ARM Cortex-M23, and Cortex-M33 cores.

Does this indicate that Infineon is releasing, or is about to release, XMC MCUs with Cortex-M23 or M33 cores?

Thank You

Read less
coresInfineonm23m33mcussegger's
  1. [Deleted User]

    Hi, Thanks for your interest in our products. This is just a standard process of including Arm core support to the Segger jlink tool, it doesn't specify any product or device from Infineon then. In the future, there might be a product that will use these standard cores. In similar cases, there willRead more

    Hi,

    Thanks for your interest in our products. This is just a standard process of including Arm core support to the Segger jlink tool, it doesn’t specify any product or device from Infineon then. In the future, there might be a product that will use these standard cores. In similar cases, there will be an official announcement from Infineon’s side.

    Best Regards,

    Vikas Nagpal

    See less
    • 0
vishalkashbar
  • 0
vishalkashbar
Asked: August 24, 2022In:
  • 0

Hi I am veritably new to CAN communication now I am working on transmitting and entering data between 2 RA2A1 MCUs but I do not know how to configure the CAN configuration on the alternate board. I have previously tested the ...Read more

Hi

I am veritably new to CAN communication now I am working on transmitting and entering data between 2 RA2A1 MCUs but I do not know how to configure the CAN configuration on the alternate board. I have previously tested the circle- reverse mode on the first board, it’s working OK , but when I connect tx and rx of the first board to the alternate board, it wasn’t working. Here is my configuration.

and then are the lines that I used to flash into the first board and alternate board, thank you in advance.

Read less
boardcirclemachinemcusra2a1Renesas Microcontroller
  1. Sandeep kumar

    Have you added the CGC driver, and started the Main Oscillator before calling R_CAN_Open()? err = R_CGC_Open (&g_cgc0_ctrl, &g_cgc0_cfg); if (FSP_SUCCESS != err) { __BKPT(0); //TODO better error handling } err = R_CGC_ClockStart (&g_cgc0_ctrl, CGC_CLOCK_MAIN_OSC, NULL); if (FSP_SUCCESS !Read more

    Have you added the CGC driver, and started the Main Oscillator before calling R_CAN_Open()?

    err = R_CGC_Open (&g_cgc0_ctrl, &g_cgc0_cfg);
    if (FSP_SUCCESS != err)
    {
    __BKPT(0); //TODO better error handling
    }
    err = R_CGC_ClockStart (&g_cgc0_ctrl, CGC_CLOCK_MAIN_OSC, NULL);
    if (FSP_SUCCESS != err)
    {
    __BKPT(0); //TODO better error handling
    }

    do
    {
    err = R_CGC_ClockCheck(&g_cgc0_ctrl, CGC_CLOCK_MAIN_OSC);
    }while(FSP_ERR_NOT_STABILIZED == err);
    if (FSP_SUCCESS != err)
    {
    __BKPT(0); //TODO better error handling
    }

    /* Initialize CAN module */
    err = R_CAN_Open(&g_can0_ctrl, &g_can0_cfg);
    /* Error trap */
    if(FSP_SUCCESS != err)
    {
    __BKPT(0); //TODO better error handling
    }

    See less
    • 0