Sign Up

Sign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.

Have an account? Sign In
Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Have an account? Sign In Now

Sign In

Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.

Sign Up Here
Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Forgot Password?

Don't have account, Sign Up Here

Forgot Password

Volt.Tech

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

Have an account? Sign In Now

You must login to ask question.

Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Forgot Password?

Need An Account, Sign Up Here

Please briefly explain why you feel this question should be reported.

Please briefly explain why you feel this answer should be reported.

Please briefly explain why you feel this user should be reported.

volt.tech Logo volt.tech Logo
Sign InSign Up

volt.tech

volt.tech Navigation

  • Home
  • About Us
  • Contact Us
Search
Ask A Question

Mobile menu

Close
Ask a Question
  • Tags
  • Category
    • Amplifiers
    • Passives & Protection
    • Clocks & Timing
    • Diodes & Rectifiers
    • FPGAs & PLDs
    • Interface ICs & Transceivers
    • LEDs & Optoelectronics
    • Memories
    • MEMS & Sensors
    • Microcontroller
    • Power Management
    • RF & Microwave
    • Security & Smart Card
    • Motor Drivers
    • Wireless Connectivity
  • Groups
  • Add group
  • Badges
  • Help
  • Home
  • About Us
  • Contact Us
Home/launch

volt.tech Latest Questions

Avs Mohan
  • 1
Avs Mohan
Asked: August 19, 2022In: Wireless Connectivity

MQTT Starts Too Slow

  • 1

When esp_mqtt_client_start was caleed, it takes 7 seconds to return connected state. Then I set up that it took lower than 1 second to connect from the launch to return OK. Is there any way to shorten the time ahead?

When esp_mqtt_client_start was caleed, it takes 7 seconds to return connected state. Then I set up that it took lower than 1 second to connect from the launch to return OK. Is there any way to shorten the time ahead?

Read less
esp32launchmqttslow
  1. Sandeep kumar
    Added an answer on August 26, 2022 at 9:57 pm

    hello,   It isn't experiencing a "bottleneck" problem. I believe that every time his device reconnects to the wifi, there is a delay. The amount of time it takes to connect to wifi can vary depending on your proximity to the network and can take several seconds. I experienced the same issue witRead more

    hello,

     

    It isn’t experiencing a “bottleneck” problem. I believe that every time his device reconnects to the wifi, there is a delay. The amount of time it takes to connect to wifi can vary depending on your proximity to the network and can take several seconds.

    I experienced the same issue with remote sensors that required deep sleep in order to conserve battery. It was necessary for a sensor to re-connect to the network after an incident that caused it to awaken from deep slumber. The system as a whole was slowed down by the normalisation of connection time required for sensor synchronisation. Espressif’s ESP-Now is the answer it offers to this specific issue.

    See less
    • 0
    • Share
      Share
      • Share on Facebook
      • Share on Twitter
      • Share on LinkedIn
      • Share on WhatsApp
  • 2 Answers
Answer

Sidebar

Ask A Question

Stats

  • Questions 395
  • Answers 382
  • Comments 0
  • Best Answers 9
  • Popular
  • Answers
  • Manoj

    Configuration using .dp vision in Infineon XDPL series IC .

    • 5 Answers
  • Linto

    Renesas RL78/G14 ADC interface code

    • 4 Answers
  • nidhi singh
    nidhi singh added an answer Hello, Yes, the software is still available, has not been… April 1, 2023 at 10:34 am
  • ashishgawade
    ashishgawade added an answer Hello, The USB-serial-JTAG port can usually reset/put the chip into… March 30, 2023 at 11:00 am
  • ashishgawade
    ashishgawade added an answer Hi Nidhi, Thanks for reaching out to Volt.Tech Engineering Community.… March 28, 2023 at 10:13 am
  • ashishgawade
    ashishgawade added an answer Hello@vikas, It's always recommended to use a bleeder of 100 ohms. Vout of the part has an offset… March 24, 2023 at 9:55 am
  • vikas Nagpal
    vikas Nagpal added an answer Hello, The SMPS reduces the power loss when VDD is… March 22, 2023 at 10:30 am

Users

test32798456

test32798456

  • 0 Questions
  • 0 Answers
test10977544

test10977544

  • 0 Questions
  • 0 Answers
test17802725

test17802725

  • 0 Questions
  • 0 Answers

Explore

  • Tags
  • Category
    • Amplifiers
    • Passives & Protection
    • Clocks & Timing
    • Diodes & Rectifiers
    • FPGAs & PLDs
    • Interface ICs & Transceivers
    • LEDs & Optoelectronics
    • Memories
    • MEMS & Sensors
    • Microcontroller
    • Power Management
    • RF & Microwave
    • Security & Smart Card
    • Motor Drivers
    • Wireless Connectivity
  • Groups
  • Add group
  • Badges
  • Help

Footer

volt.tech

Volt.Tech

Find your spark

About Us

  • About Us
  • Contact Us
  • Groups

Legal Stuff

  • Privacy Policy
  • Faqs

Follow

© 2022 volt.tech. All Rights Reserved
With Love by volt.tech.