Sign Up

Sign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.

Have an account? Sign In
Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Have an account? Sign In Now

Sign In

Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.

Sign Up Here
Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Forgot Password?

Don't have account, Sign Up Here

Forgot Password

Volt.Tech

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

Have an account? Sign In Now

You must login to ask question.

Continue with Facebook
Continue with Google
or use

What is the capital of Egypt? ( Cairo )

Forgot Password?

Need An Account, Sign Up Here

Please briefly explain why you feel this question should be reported.

Please briefly explain why you feel this answer should be reported.

Please briefly explain why you feel this user should be reported.

volt.tech Logo volt.tech Logo
Sign InSign Up

volt.tech

volt.tech Navigation

  • Home
  • About Us
  • Contact Us
Search
Ask A Question

Mobile menu

Close
Ask a Question
  • Tags
  • Category
    • Amplifiers
    • Passives & Protection
    • Clocks & Timing
    • Diodes & Rectifiers
    • FPGAs & PLDs
    • Interface ICs & Transceivers
    • LEDs & Optoelectronics
    • Memories
    • MEMS & Sensors
    • Microcontroller
    • Power Management
    • RF & Microwave
    • Security & Smart Card
    • Motor Drivers
    • Wireless Connectivity
  • Groups
  • Add group
  • Badges
  • Help
  • Home
  • About Us
  • Contact Us
Home/devkit

volt.tech Latest Questions

nidhi singh
  • 0
nidhi singh
Asked: December 19, 2022In: Wireless Connectivity

ESP32- C3 Mini Devkit Configure for Built in USB JTAG?

  • 0

Hello and thanks in advance for the help. I recently entered my ESP32- C3 mini development kit. I’m sure it’s configured to use the CP2102 USB interface, so R1 and R4 are installed. I want to use the internal USB JTAG ...Read more

Hello and thanks in advance for the help.

I recently entered my ESP32- C3 mini development kit. I’m sure it’s configured to use the CP2102 USB interface, so R1 and R4 are installed. I want to use the internal USB JTAG interface which I understand requires the removal of R1 and R4 and the installation of R2 and R3( though I’m not sure this is the case). This would also free up RXD and TXD, which I need to use.

I haven’t been suitable to find documentation on how to use the Devkits with the USB JTAG, nor have I been suitable to determine the position of R1, R2, R3, and R4. I’ve tried” beeping out” the circuit but would prefer not to ruin my board.

Is there any guidance as to where those components are and/ or how to use a USB JTAG?

Read less
c3minidevkitesp32jtagusb
  1. Alex thomas
    Added an answer on December 20, 2022 at 11:49 am

    The PCB layout of that dev board can be found then. As far as I can see, you need to rotate those resistors 90 degrees to move them from the red to the green position in this image: You probably also want to disconnect the RxD/TxD pins from the CP2104 to the ESP32C3 if you want to use those pins. YoRead more

    The PCB layout of that dev board can be found then. As far as I can see, you need to rotate those resistors 90 degrees to move them from the red to the green position in this image:

    You probably also want to disconnect the RxD/TxD pins from the CP2104 to the ESP32C3 if you want to use those pins. You can do that by removing R21/R22, I marked those in blue.

    The built-in USB thing should more or less work as an extra UART inside the ESP32C3 and as a general CDC- ACM serial port(=no drivers needed) on the PC side. You do need to use the latest master of ESP-IDF to get full support for it, and if you specifically want to select the device as your press output UART in menuconfig, else, your debug messages will go to UART0.

    On the JTAG side, just useesp_usb_jtag. cfg as your JTAG adapter, config file in OpenOCD and you should be good.
    Still, feel free to post it here, If you need any further help. Support for the built-in USB-to-JTAG thing on the C3 is enough new, so I’d be interested in seeing how you fare with it.

    See less
    • 0
    • Share
      Share
      • Share on Facebook
      • Share on Twitter
      • Share on LinkedIn
      • Share on WhatsApp
  • 1 Answer
Answer

Sidebar

Ask A Question

Stats

  • Questions 449
  • Answers 436
  • Comments 0
  • Best Answers 9
  • Popular
  • Answers
  • Manoj

    Configuration using .dp vision in Infineon XDPL series IC .

    • 5 Answers
  • Linto

    Renesas RL78/G14 ADC interface code

    • 4 Answers
  • sachinsharma
    sachinsharma added an answer Hi @Farmanali, Infineon has a pervasive and wide range of… September 25, 2023 at 10:16 am
  • Alex thomas
    Alex thomas added an answer Hello, Right, existing LED drivers all have PWM engines. It… September 19, 2023 at 11:10 am
  • Julian White
    Julian White added an answer Hello, You should set handshake after setting property RtsEnable =… September 14, 2023 at 10:59 am
  • Julian White
    Julian White added an answer Hello @Vikas, Thanks for posting your question online. Yes, one… September 12, 2023 at 10:33 am
  • Alex thomas
    Alex thomas added an answer Hi @sachinsharma, XDPL8221 has a PWM dimming interface which is… September 4, 2023 at 11:01 am

Users

urvashimorar

urvashimorar

  • 0 Questions
  • 0 Answers
test7457901

test7457901

  • 0 Questions
  • 0 Answers
test43764860

test43764860

  • 0 Questions
  • 0 Answers

Explore

  • Tags
  • Category
    • Amplifiers
    • Passives & Protection
    • Clocks & Timing
    • Diodes & Rectifiers
    • FPGAs & PLDs
    • Interface ICs & Transceivers
    • LEDs & Optoelectronics
    • Memories
    • MEMS & Sensors
    • Microcontroller
    • Power Management
    • RF & Microwave
    • Security & Smart Card
    • Motor Drivers
    • Wireless Connectivity
  • Groups
  • Add group
  • Badges
  • Help

Footer

volt.tech

Volt.Tech

Find your spark

About Us

  • About Us
  • Contact Us
  • Groups

Legal Stuff

  • Privacy Policy
  • Faqs

Follow

© 2022 volt.tech. All Rights Reserved
With Love by volt.tech.