Hi, Kindly do let me know their is any fault pin detection for PWM fault in R5F104BG Regards
Hi,
Kindly do let me know their is any fault pin detection for PWM fault in R5F104BG
Regards
Read lessSign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
You must login to ask question.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
Hi, i am using Dialog BLE module in one project. And i want to interface this module with external MCU. So can i connect this module to RX/TX MCU without any program. Thanks & Regard Raja
Hi,
i am using Dialog BLE module in one project. And i want to interface this module with external MCU.
So can i connect this module to RX/TX MCU without any program.
Thanks & Regard
Raja
Read lessDear Sir, Please do let me know Can we use as AT command in DA14531 BLE module. Regards Raja
I am working on a project and with Renesas R5F100FC MCU in this project. Problem is that my E1 emulator is not working, before E1 Emulator was working fine. How can I check if the E1 emulator is ok ?
I am working on a project and with Renesas R5F100FC MCU in this project. Problem is that my E1 emulator is not working, before E1 Emulator was working fine.
How can I check if the E1 emulator is ok ?
Read lessHi, You can download E1 emulator self check programmer from Renesas website. then follow the instruction manual to check E1 emulator. Regards Shivali Singh
Hi,
You can download E1 emulator self check programmer from Renesas website.
then follow the instruction manual to check E1 emulator.
Regards
Shivali Singh
See lessI am using Renesas RA2L1 example code on CAN but my CAN is not working/not received data CAN analyzer.
I am using Renesas RA2L1 example code on CAN but my CAN is not working/not received data CAN analyzer.
Read lessDear Raja Singh, You need to their CAN ic hardware is it ok or not, and which IC you are using for CAN? Regards Shivali Singh
Dear Raja Singh,
You need to their CAN ic hardware is it ok or not, and which IC you are using for CAN?
Regards
Shivali Singh
See lessHow to use MD pin in Flash time or Debug time or how to program Renesas RA2L1 MCU by using Renesas flash programmer ?
How to use MD pin in Flash time or Debug time or how to program Renesas RA2L1 MCU by using Renesas flash programmer ?
Read lessHi mr. Raja You have to make MD pin active low while SCI boot (flashing with UART ) & if you want to debug the make it high with 10 K pullup & isolate pull down resistor
Hi mr. Raja
You have to make MD pin active low while SCI boot (flashing with UART )
& if you want to debug the make it high with 10 K pullup & isolate pull down resistor
See lessI am working on Renesas RA2L1 kit , my code finalize on Renesas kit, now we are going to make PCB , for this PCB I want to know about programming pin connector. Can you help to share programming pin ...Read more
I am working on Renesas RA2L1 kit , my code finalize on Renesas kit, now we are going to make PCB , for this PCB I want to know about programming pin connector. Can you help to share programming pin connector so that I can make one my PCB.
Read lessHi Shivali Sir , I am working Renesas MCU R5F1027ANA (RL78/G12), I am facing the reset problems regularly in my code, please help me to resolve this problems. Regards Raja Singh Livguard
Hi Shivali Sir ,
I am working Renesas MCU R5F1027ANA (RL78/G12), I am facing the reset problems regularly in my code, please help me to resolve this
problems.
Regards
Raja Singh
Livguard
Read lessIn Renesas CS+ CC IDE, where I can see the running variable in watch window because I want to see timer values in Running time, please do let me their is option in Renesas RL78/CS+CC to see the running time ...Read more
In Renesas CS+ CC IDE, where I can see the running variable in watch window
because I want to see timer values in Running time, please do let me their is option in Renesas RL78/CS+CC to see the running time variable values in watch window.
Please help here asap.
How to make input or output pin without code generator in Renesas RL78 CS+CC IDE.
How to make input or output pin without code generator in Renesas RL78 CS+CC IDE.
Read lessDear Raja, Please check the below instruction to make input and output without code generator. PM1_bit.no0 = 0; // 0 mean Ouput make, 1 means Input make P1_bit.no = 1; // high pin // Port Pin P10 Please feel free to write us for further support. Thanks & Regards Shivali Singh AppliRead more
Dear Raja,
Please check the below instruction to make input and output without code generator.
PM1_bit.no0 = 0; // 0 mean Ouput make, 1 means Input make
P1_bit.no = 1; // high pin // Port Pin P10
Please feel free to write us for further support.
Thanks & Regards
Shivali Singh
Application Engineer
See less
Hi Sir , Yes you can use AT commands for Dialog BLE Refer below link http://lpccs-docs.renesas.com/UM-140-DA145x-CodeLess/atcommands.html Thanks !
Hi Sir ,
Yes you can use AT commands for Dialog BLE
Refer below link
http://lpccs-docs.renesas.com/UM-140-DA145x-CodeLess/atcommands.html
Thanks !
See less