Firmware status code read-out procedures with debug mode?
Firmware status code read-out procedures with debug mode?
Read lessSign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
You must login to ask question.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
Firmware status code read-out procedures with debug mode?
Firmware status code read-out procedures with debug mode?
Read lessDoes the body diode affect ZVS behavior and GaN can be used ?
Does the body diode affect ZVS behavior and GaN can be used ?
Read lessHow many times we can burn or test program in XDPL8210 IC ?
How many times we can burn or test program in XDPL8210 IC ?
Read lessI want to develop 250W led driver using LLC topology, please suggest a solution or IC in Infineon?
I want to develop 250W led driver using LLC topology, please suggest a solution or IC in Infineon?
Read lessI am getting error to update firmware when trying to burn program in XDPL8210 IC using .dpvision tool. Please advise some solution ?
I am getting error to update firmware when trying to burn program in XDPL8210 IC using .dpvision tool.
Please advise some solution ?
Read lessAs the XDPL8210 chip on the 35 W reference design PCB has a first full set of parameters in its One-Time Programmable (OTP) memory space, only changed parameters are written in the OTP memory. 1 Load configuration file (see example in Figure 7). 2 Modify the parameter value needed, then press [File]Read more
As the XDPL8210 chip on the 35 W reference design PCB has a first full set of parameters in its One-Time
Programmable (OTP) memory space, only changed parameters are written in the OTP memory.
1 Load configuration file (see example in Figure 7).
2 Modify the parameter value needed, then press [File] >> [Save] or [File] >> [Save as] to save
the configuration file. Otherwise, proceed to step 3.
3
(optional)
Disconnect or turn off AC input voltage and check the hardware connection for configuration,
see Figure 2 and Figure 3.
4 Press to supply power and establish connection to the target XDPL8210. After this,
XDPL8210 will enter configuration mode and the device status should change to .
5
Press to burn the configuration into target XDPL8210.
After this step, a window pops up, like one of these below.
Note: If the parameter configuration is equivalent to to the pre-existing parameters, the
XDPL8210 will not burn them in the OTP memory.
6 Press “Proceed” or “Yes” to burn the configuration. After this, a window pops up indicating
success.
7 Press “OK” on the pop-up window then disconnect the programming cable from the board
connector and test the application, if needed.
How to configure Infineon CDM10VD dimming IC ?
How to configure Infineon CDM10VD dimming IC ?
Read lessHi Manoj, Please find below, the answer to your query. Please go thorough the pg no 25-26 fo the given link. Please find the link below. https://www.infineon.com/dgdl/Infineon-ApplicationNote_ReferenceBoard_REF-XDPL8105-CDM10V-ApplicationNotes-v02_00-EN.pdf?fileId=5546d462584d1d4a0158962cb4ed4315
Hi Manoj,
Please find below, the answer to your query.
Please go thorough the pg no 25-26 fo the given link. Please find the link below.
https://www.infineon.com/dgdl/Infineon-ApplicationNote_ReferenceBoard_REF-XDPL8105-CDM10V-ApplicationNotes-v02_00-EN.pdf?fileId=5546d462584d1d4a0158962cb4ed4315
How to configure or program Infineon XDPL series IC using .dp vision tool from Infineon?
How to configure or program Infineon XDPL series IC using .dp vision tool from Infineon?
Read lessplz 8 pin connector interface( location TARGET) pin numbering image?
plz 8 pin connector interface( location TARGET) pin numbering image?
See lessHow to connect or access UART with .dp vision Gen 2 with XDPL series IC.
How to connect or access UART with .dp vision Gen 2 with XDPL series IC.
Read lessHi Manoj. Connection needs to be done b/w .dp Vision Gen2 Pin 2,3 &4. Where • Pin 4 is VCC • Pin 2 is GND • Pin 3 is UART Connect accordingly.
Hi Manoj.
Connection needs to be done b/w .dp Vision Gen2 Pin 2,3 &4. Where
• Pin 4 is VCC
• Pin 2 is GND
• Pin 3 is UART
Connect accordingly.
Procedures for firmware status code read-out in debug mode Steps 1. Open the configuration file (see the example in Figure 33) used in the system which has the problem of powering up or shutting down, then set the DebugMode parameter to “Enabled”. 2. Ensure that the AC input to the board is switchedRead more
Procedures for firmware status code read-out in debug mode
Steps
1. Open the configuration file (see the example in Figure 33) used in the system which has the problem of powering up or shutting down, then set the DebugMode parameter to “Enabled”.
2. Ensure that the AC input to the board is switched off and that the hardware connection for configuration is OK based on Figure 32, plus a low-ESR ceramic capacitor of 1 nF soldered across the UART pin and ground for noise decoupling.
3. Click to supply power and establish connection to the target XDPL8210. After this step, the XDPL8210 will be in configuration mode and the device status should change to.
4. Supply the board with AC input and output conditions, which trigger the problem. After this step, the board does not start up because XDPL8210 is still in configuration mode.
5. Click to test the configuration with the target XDPL8210.
After this step, the IC will automatically start up in debug mode and you should see a pop-up window like the one shown below. If any protection is triggered, the IC’s GD pin will stop switching and the output will stay low.
6. Click “OK” in the pop-up window.
7. Click the “Refresh” button in the .dp Vision application section and switch off the AC input. After this step, the firmware status code is read out. If any protection has been triggered after step 5, the status code will show a value in red. Otherwise, it will show 0x0000 in black.
8. Hover the mouse over the status code and the description of the status code will be shown. For example, 0x0040 means input UVP has been triggered.
9. Apply the necessary counter-measure or repeat the steps above to debug again. Otherwise, ensure
See lessthe AC input is switched off before disconnecting the programming cable from the XDPL8210
board.