When using the PI7C7300 in hot-swap hardware, which Voltage Source Supply do I connect it to?
When using the PI7C7300 in hot-swap hardware, which Voltage Source Supply do I connect it to?
Read lessSign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
You must login to ask question.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
When using the PI7C7300 in hot-swap hardware, which Voltage Source Supply do I connect it to?
When using the PI7C7300 in hot-swap hardware, which Voltage Source Supply do I connect it to?
Read lessAre Diodes’ dual transistor devices, such as the MMDT series, made with monolithic die?
Are Diodes’ dual transistor devices, such as the MMDT series, made with monolithic die?
Read lessYes, Diodes manufactures its binary transistor products using separate die which are wire clicked to the lead frames. They aren't monolithic devices.
Yes, Diodes manufactures its binary transistor products using separate die which are wire clicked to the lead frames. They aren’t monolithic devices.
See lessHow to protection methods for Reverse polarity?
How to protection methods for Reverse polarity?
Read lessThe selection criteria will depend on, how fast your fuse will blow. firstly, you need to identify what is your short circuit current sourcing capacity of your Input DC Source. then how fast (means within what time) your selected fuse will get blown. based on that arcing current you can choose the dRead more
The selection criteria will depend on, how fast your fuse will blow.
firstly, you need to identify what is your short circuit current sourcing capacity of your Input DC Source.
then how fast (means within what time) your selected fuse will get blown.
based on that arcing current you can choose the diode which is conducting throughout that arcing time of the fuse.
selection of that diode is in such a way that, the diode surge current should be at least 2.5 times the arcing current of the fuse within that time.
See lessPlease suggest topology and IFX IC for >200W Led Drivers?
Please suggest topology and IFX IC for >200W Led Drivers?
Read lessHi Manoj we suggest batter ISL and XDPL series and there is used for Two stage Flyback and PFC +LLC , Part no:-XDPL8221 & ICL5102. Thanks
Hi Manoj
we suggest batter ISL and XDPL series and there is used for Two stage Flyback and PFC +LLC , Part no:-XDPL8221 & ICL5102.
Thanks
See lessI am working with your modules and need now your support. Can you tell me where I can find any guide about thermal cycling capability of Infineon’s modules?
I am working with your modules and need now your support.
Can you tell me where I can find any guide about thermal cycling capability of Infineon’s modules?
I am looking for a mosfet which would be appropriate for essentially DC switching of a 400V 7A continuous load. Low RDS on is preferred as I have limited ability to remove heat easily.?
I am looking for a mosfet which would be appropriate for essentially DC switching of a 400V 7A continuous load. Low RDS on is preferred as I have limited ability to remove heat easily.?
Read lessHi, There is a very wide portfolio of MOSFETs under Infineon which you may explore using below link, where you can further filter out suitable device with additional parametric filters. https://www.infineon.com/cms/en/product/power/mosfet/n-channel/ Please let us know if you require further assistanRead more
Hi,
There is a very wide portfolio of MOSFETs under Infineon which you may explore using below link, where you can further filter out suitable device with additional parametric filters.
https://www.infineon.com/cms/en/product/power/mosfet/n-channel/
Please let us know if you require further assistance on this topic.
See lessI have question about how to use Coss of SIC MOSFET to calculate right Qoss?
I have question about how to use Coss of SIC MOSFET to calculate right Qoss?
Read lessYou can use this formulaΒ Qoss = Coss*VDS. For Qoss calculation please consider Co(tr), if it is not available you can use Coss.
You can use this formulaΒ Qoss = Coss*VDS.
For Qoss calculation please consider Co(tr), if it is not available you can use Coss.
See lessForward Current through the Body diode of mosfet when its OFFΒ ?
In the simulation itself you can check the drain current, negative current will be the body diode current.
In the simulation itself you can check the drain current, negative current will be the body diode current.
See lessWhat is the recommended operating condition of IRS2110?
What is the recommended operating condition of IRS2110?
Read lessHi, The device's logic is operational for a Vs (High-side floating supply offset voltage) from -4V to +500V. for more detail please go with below link https://www.infineon.com/dgdl/Infineon-IR2110-DataSheet-v01_00-EN.pdf?fileId=5546d462533600a4015355c80333167e Thanks
Hi,
The device’s logic is operational for a Vs (High-side floating supply offset voltage) from -4V to +500V. for more detail please go with below link
Thanks
See lessHow to calculate Gout,loss?
How to calculate Gout,loss?
Read lessPlease find the formula for calculating Gout,loss below. πΊππ’π‘,πππ π =(ΞπΌππ’π‘,πππ,ππ‘,ππ΄πΆ,πππ₯ + ΞπΌππ’π‘,πππ,ππ‘,ππ΄πΆ,πππ)/{ 2 β (ππΏπΈπ·,πππ₯,ππ‘,πΌ,ππ’π‘,πππβ ππΏπΈπ·,πππ,ππ‘,πΌ,ππ’π‘,πππ)}
Please find the formula for calculating Gout,loss below.
πΊππ’π‘,πππ π =(ΞπΌππ’π‘,πππ,ππ‘,ππ΄πΆ,πππ₯ + ΞπΌππ’π‘,πππ,ππ‘,ππ΄πΆ,πππ)/{
2 β (ππΏπΈπ·,πππ₯,ππ‘,πΌ,ππ’π‘,πππβ ππΏπΈπ·,πππ,ππ‘,πΌ,ππ’π‘,πππ)}
According to the hot- exchange specification modification 1.0., the ground should be linked to early power. All other chips on the board should be connected to switched power, which comes latterly, driven from the Hot- exchange regulator.
According to the hot- exchange specification modification 1.0., the ground should be linked to early power. All other chips on the board should be connected to switched power, which comes latterly, driven from the Hot- exchange regulator.
See less