Can you please provide Cypress TSSI tool?
Can you please provide Cypress TSSI tool?
Read lessSign Up to our social questions and Answers Engine to ask questions, answer people's questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people's questions & connect with other people.
Volt.Tech
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
You must login to ask question.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
Trying to program some blank parts in DA9063-EVAL1.The motherboard looks to have a boost circuit to generate the 7.5V for programming, but I can’t get that to work. Please confirm the right jumper setting and TP select switch settings for ...Read more
Trying to program some blank parts in DA9063-EVAL1.The motherboard looks to have a boost circuit to generate the 7.5V for programming, but I can’t get that to work. Please confirm the right jumper setting and TP select switch settings for OTP programming.
Read lessThe switch on the left hand side should put the board into either programming mode or Power commander mode(emulation). Programming mode should enable the boost.
The switch on the left hand side should put the board into either programming mode or Power commander mode(emulation).
Programming mode should enable the boost.
See lessJust received a DA9063-EVAL1 and while attempting to program some blank parts. The motherboard looks to have a boost circuit to generate the 7.5V for programming, but I can’t get that to work. Can you please confirm the right jumper ...Read more
Just received a DA9063-EVAL1 and while attempting to program some blank parts. The motherboard looks to have a boost circuit to generate the 7.5V for programming, but I can’t get that to work. Can you please confirm the right jumper setting and TP select switch settings for OTP programming?
Read lessAre there any Renesas DA9063 PMIC Configurartions readily available for Xilinx Zynq Ultrascale+ 4EV devices. Based on my power/sequencing requirements, I need at least two Renesas DA9063. 1. Can several PMICS be sequenced between each other? 2. Can any of the 11 ...Read more
Are there any Renesas DA9063 PMIC Configurartions readily available for Xilinx Zynq Ultrascale+ 4EV devices.
Based on my power/sequencing requirements, I need at least two Renesas DA9063.
1. Can several PMICS be sequenced between each other?
2. Can any of the 11 LDO’s be combined in parallel as long as they are configured for the same slot and voltage?
3. Besides (Buckcore1 + Buckcore2), (BuckMem + BuckIO) can any other bucks be combined in parallel?
4. I have ordered blank 00 devices, do they have to be programmed before they are soldered to the boards?
The DA9063-A is a flexible, scalable system PMIC capable of powering a wide range of multicore SoCs, FPGAs, memory subsystems, and peripherals. Full power tree management and multiple sleep modes result in a power-efficient system solution suitable for infotainment, telematics, and ADAS applicationsRead more
The DA9063-A is a flexible, scalable system PMIC capable of powering a wide range of multicore SoCs, FPGAs, memory subsystems, and peripherals. Full power tree management and multiple sleep modes result in a power-efficient system solution suitable for infotainment, telematics, and ADAS applications. The device includes eleven LDOs with programmable output voltages providing up to 300 milliamps and six high-current buck converters providing up to two and a half amps per buck. Any two bucks can be combined in a dual-phase configuration providing up to 5 amps.
See lessI have an Espressif ESP32 running a lighting circuit. When I switch the circuit on the ESP gets power and the ESP is programmed to switch on a relay (connected to a light) in the setup routine. The relay switch-on ...Read more
I have an Espressif ESP32 running a lighting circuit.
When I switch the circuit on the ESP gets power and the ESP is programmed to switch on a relay (connected to a light) in the setup routine.
The relay switch-on is practically the first command after initializing the GPIO pins in the setup routine.
My problem is that on some occasions the relay switches on within 500ms of the circuit being powered (which is acceptable) and other times there is a delay of about 20-30 seconds before the relay is activated.
What would cause this and how can I fix it?
I have Renesas RH850F1K (R7F701649) microcontroller and using CS+ IDE. How to set the LED1,if it is connected to P0_11? I want to toggle this LED1.
I have Renesas RH850F1K (R7F701649) microcontroller and using CS+ IDE. How to set the LED1,if it is connected to P0_11? I want to toggle this LED1.
Read lessThe hardware User Manual contains the information required to access I/O and peripherals among other things. RH850/F1KM, RH850/F1KH User's Manual: Hardware (R01UH0684EJ0110) Sample code is available to demonstrate many of the concepts.
The hardware User Manual contains the information required to access I/O and peripherals among other things. RH850/F1KM, RH850/F1KH User’s Manual: Hardware (R01UH0684EJ0110) Sample code is available to demonstrate many of the concepts.
See less
Where is the FCU Firmware ? It is already present in the ECC test area or is provided by Renesas?
Where is the FCU Firmware ? It is already present in the ECC test area or is provided by Renesas?
Read lessThe FW is stored in a special area of the flash. The copy of the data from this area stored into the FCU RAM is either handled in the libraries or described in the flash hardware user's manual. For more details please contact: device_support.RH850-EU at lm.renesas.com
The FW is stored in a special area of the flash. The copy of the data from this area stored into the FCU RAM is either handled in the libraries or described in the flash hardware user’s manual. For more details please contact: device_support.RH850-EU at lm.renesas.com
See lessIn reference manual of Renesas RH850/P1x microcontroller I want to know more about Clock Configuration for this device. CKSCnCTL — Clock Selection Control Register n (n = 0, 1) CKSCnCTL— Clock Selection Status Register n (n = 0, 1) CLKDnDIV ...Read more
In reference manual of Renesas RH850/P1x microcontroller I want to know more about Clock Configuration for this device. CKSCnCTL — Clock Selection Control Register n (n = 0, 1) CKSCnCTL— Clock Selection Status Register n (n = 0, 1) CLKDnDIV — Clock Division Register n (n = 0, 1) CLKDnSTAT — Clock Status Register n (n = 0, 1). Here two control registers 0 and 1 (CKSC0CTL and CKSC1CTL) are available. So, which one I have to select to configure for clock selection and when should I use CKSC0CTL or CKSC1CTL.
Read lessPlease take a glance to the diagram 12.1 in the User's Manual: There are two clock output pins available (0 & 1). Therefore, also two sets of registers are available.
Please take a glance to the diagram 12.1 in the User’s Manual: There are two clock output pins available (0 & 1). Therefore, also two sets of registers are available.
See less
PFA is the TSSI tool for windows.
PFA is the TSSI tool for windows.
See less